Site Loader

Download Heatline C28 manual. You have chosen to download this manual. Heatline C28, please click on the PDF link below. The boiler’s ‘Log Book’ must be completed at each Service visit. By means of a manual switch the C24/C28 can be set to operate in one of two operating modes, . Boiler Manuals for the Heatline Compact C28 appliance.

Author: Zolokree Yoshura
Country: Angola
Language: English (Spanish)
Genre: Art
Published (Last): 5 February 2006
Pages: 100
PDF File Size: 20.16 Mb
ePub File Size: 11.8 Mb
ISBN: 422-3-80218-122-1
Downloads: 23811
Price: Free* [*Free Regsitration Required]
Uploader: Dujora

Verify the fuses connections. You can select the category of spares you are looking for and which appliance brand your spares are a part of. If seals are damaged- hewtline as necessary 8.

Primary pressure sensor will turn off your appliance whenever the circuit pressure will fall heatlune 0. Re-assemble in reverse order Fan replacement 1. Verify the sensor F20 Overheating fault Verify the operation of the pump.

Saunier Duval Boiler Parts. Remove the air pressure switch by pulling forward off its bracket 6.


Ensure all joints are sound. The comustion chamber should now be removed, It can be achived by unscrewing all four side screws 6. Screws, Nuts, Bolts and Clips. British Gas Boiler Spares. No hot water and no central heating. Signup to our newsletter today Sign up. Replace faulty sensors F85 Flow and return heating sensors fault Verify temperature sensors connections F86 Underfloor heating contact fault Verify the sensor connections.

When the demand for central heating is fulfilled, the burner will shut down and the appliance will come to stand-by mode, until the next hot water or heating demand. Disconnect the electrical connections to gas valve modulating coil 5.

Heatline | Literature

Share This Page Tweet. I appreciate everyones replies Gary. If you continue to experience problems please click here c2 contact information. Discussion in ‘ Central Heating Forum ‘ started by bluecrushOct 21, Remove the clop on the pump body and then release the pipe of the expansion vessel as shown on the picture below 6. Remove the interface cover by lifting the two latches 4. I have manula in the past that you fix one part for the phone to ringing in a week and it’s packed up again.


The air pressure switch is located on the top of the expansion vessel 4. Re-assemble in reverse order Attention! Your boiler should work reliably for a number of years if it is serviced annually, however occassionaly faults can occur. Collectively we have over years of experience in boiler spares identification and spares distribution.

By continuing to use this site, you are agreeing to our use of cookies. Yes Replace gas supply, pressure or gas valve No hot water and no central heating Open a hot tap to create a demand — is there a spark at the ignition electrode? I am surprised that it runs for as long as 30 seconds then. In the manual this part was as listed above. Verify the sensor connections.

Boiler parts Each Heatline boiler is equipped with following additional parts: You’re safe shopping with us.

This now would make sense mznual it was overheating the night before so he advised to replace this part. Re-set function Whenever boiler gets locked out, you should verify the gas supply and ionisation probe position.

Port valve can be found on the hydro-block.

Asbestos 1 Jul Unclip the sensor from the pipe 5. Yes, my password is: Disconnect the electrical leads of low pressure sensor 8. However, first you should check the rads are all turned on.


For items in stock and ordered before 8pm we will dispatch the same day for manuall on the next working day. After activating this function system will need to be manually re-set.

While waiting for a replacement part the insurance happened to call out and change the DHW sensor as this was the one flashing on the front panel and showing up as the error.

Heat Line C28 Manuals

We have created a special troubleshooting guide which you can access by clicking here which may help you resolve the issue. Boiler normal operation Your appliance can be set to work either on domestic hot water and heating or domestic hot water only. Verify the boards reference F71 Flow heqtline temperature sensor fault Verify the sensor connections.

Hi Tony, this is starting to cheese me off mate, it has been going on for a while. Replace the heat exchanger. Vaillant Group reserves the right to amendupdate, or withdraw any information within the help centre without prior notice. Mabual sure that the sensor is clipped to the tube. Verify temperature sensors connections. Open the isolating valves on flow and return connections, refill, vent and re-pressurise system ensuring the all joints are sound.

I was out on a job and was not their when he kanual arrived so told him over the phone to check the “overheat sensor” even though this light was not flashing.