Site Loader

FTR-F1CAV Specifications: Manufacturer: Fujitsu ; Product Category: General Purpose Details, datasheet, quote on part number: FTR-F1CAV. FTR-F1CAV-RG from Fujitsu Limited. Find the PDF Datasheet, Specifications and Distributor Information. FTR-F1CAV datasheet, FTR-F1CAV circuit, FTR-F1CAV data sheet: FUJITSU – POWER RELAY 2 POLES-5 A LOW PROFILE TYPE,alldatasheet.

Author: Vudojora Fausar
Country: Netherlands
Language: English (Spanish)
Genre: Software
Published (Last): 16 April 2014
Pages: 259
PDF File Size: 1.73 Mb
ePub File Size: 14.83 Mb
ISBN: 658-3-12585-654-4
Downloads: 49689
Price: Free* [*Free Regsitration Required]
Uploader: Daramar

This caused the 2nd LED to light up in Figure Charles Platt February 5, at 5: Spencer October 4, at 8: Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical realys. I’m extremely frustrated and feel like tossing the whole thing.

f1ca012v datasheet pdf ibm

These products may also interest you. No marking on individual relays. To display the correct break-down of prices with or without VATplease select:.

We highly recommend that you confirm your actual solder conditions. I even tried changing just slightly the wiring datasheeg the box but to no avail at all.

FTR-F1CA012V

Enter contact details Add further articles on request. Relays produced after datasjeet specific date code that is indicated on each data sheet are lead-free. When I got to this exercise I got everything wired up and it didn’t work. I purchased both component packs and took apart the relay that’s the one I’m using. Labels Shopping List 8 contest 3 Intro 1 errata 1.

Now I am going to go back and set up exercise 7 again and get it to work right. View my complete profile. Product specification Product description Downloads Environmentally relevant information Product specification. Relay pin functions do tend to vary. However, I’m a bit stuck at the breadboarding stage of Experiment Reflow Solder condtion Flow Solder condtion: We highly recommend datsheet you confirm your actual solder conditions 3.

  EUROMODELISMO 109 PDF

Jasony April 23, at 5: Most of our signal and power relays are lead-free. Posted by James Floyd Kelly Jim at 8: I’m having datasjeet the same problem.

บริษัท อีเลคทรอนิคส์ ซอร์ซ จำกัด

v1ca012v When I was building my circuit, I was using dataasheet relay where the arm was pointing towards the coil when not powered When the f1ca0112v is powered, the magnetic field it creates pushes the arm away upward.

If I had to modify the circuit in FigureI’d have to show the anode of the diode connected to the right-most pins the one the arm is shown pointing at in Fig We are there for you. I’m solving them little by little, but I still think there’s a discrepancy in the drawings for relays in the book – for Chapter 2, when unpowered, your drawing shows exactly what I see when I took a relay apart the one you recommend – when unpowered, the arm is pointing towards the coil.

I’m losing track of your sequence, James! I rewired the circuit a couple of times to no avail and then decided to move on.

FTR-F1CAV Fujitsu | Ciiva

Offers on quantities below or above the set amounts. When I open the switch, it sets off the alarm, but the relay won’t self-lock, and closing the switch turns the alarm off. Well I guess I’ve had beginners luck because the breadboarding went fine and so did the prototyping board.

Funny that I’ve managed to get this far in the book without having to do this.

  LIPI 6605 PDF

I am a new customer. Dipped SnAgCu solder is known as low risk tin whisker. Take advantage of our reeling service!

Miniature power relay, 2 changeover, 24 VDC, 5 A. We use cookies to save your settings and to immediately show you the right price information next time you visit our site. To speed up your production processes we will support you with a free-of-charge reeling service for a wide range of components.

Not sure which problems you still have, and which you have managed to solve. The drawing for Exercise f1c0a12v shows the arm of the relay, when the coil isn’t powered, pointing in the f1ca102v of the coil. It has been verified that using lead-free relays in leaded assembly process will not cause any.

The e-mail address will not be used for marketing purposes other than providing your recommendation. I forgot to use heat sinks, so maybe I over heated the pushbutton. Registration for newsletter Would you like to stay up to date and inform yourself about products, services and offers?

I thought my relays could be bad. Send copy datasyeet my e-mail address. Platt but I can read the schematic he did and follow the diagram as well. I order some different pushbuttons at are the same except the new ones are 3A and not 1A.

I’ve stared at the datasheet for the relay but I can’t see an answer there.