Site Loader

Buy B DANFOSS REFRIGERATION EKC D1, ller, I-pack the best price, fast worldwide shipping, up to 65% discount DANFOSS. EKC controllers can be used for a wide range of different refrigeration applications .. Regolatore per il controllo della temperatura – EKC D1, Literature. I need some help on this danfoss EKC D1. Its controlling a small freezer unit The set-point temperature is ยบ The R1 seting is diferential is.

Author: Fegis Shashakar
Country: Egypt
Language: English (Spanish)
Genre: Politics
Published (Last): 17 July 2009
Pages: 74
PDF File Size: 3.80 Mb
ePub File Size: 20.5 Mb
ISBN: 679-8-67416-442-5
Downloads: 14814
Price: Free* [*Free Regsitration Required]
Uploader: Tojanos

The value is the same as that set for the night increase value, but it is only raised if the value is positive. An A alarm will not be visible as long as there is an ekkc E alarm.

Upper alarm limit Here you set when the alarm for high temperature is to start. But before you change the value, you must have access to the menu.

Continue session

Copying to copying key incorrect. Danfoss EKC D1 temperature settings The sensor is correct, i change the other controller whit other freezer and the problem goes with the controller I went to the store and got a new one and the problem is solved.

If a defrost start via data communication does not take place, the interval time will 202×1 used as max.

Programmable Controls Electronic Controls: I change the controller from one freezer to another one, to rule out problems on the freezer, and the problem is in the controller. Temperature difference for night time cover When the night time cover is placed over the appliance, the difference between the S3 and S4 sensors will fall due to elc reduced cooling loss.

  CHARLES BUKOWSKI CRONICA DE UM AMOR LOUCO PDF

Defrost 10 6 A DO3.

ekv Refrigeration stopped by main switch. The controller will register when the DI input is activated. The input is not used 1 Status display of a contact function 2 Door function. Sensors S3 and S4 are thermostat sensors. But you can also use a sensor with another signal accuracy.

Push the upper or the lower button and ec the new value 5. Push the uppermost or lowermost button to scan the rolling stack. On the network a cleaning alarm is transmitted to the system unit.

The relay cuts in when rail heat is to operate Light: C30 set to on so relay acts inversely?

The timer function starts when voltage is connected to the controller, but it is displaced the first time by the setting in d The clock function can thus be protected during 202dd1 power failure. The limit value is raised during night operation. The thermostat sensors are either placed in the cold air flow after the evaporator, in the warm air flow just before the evaporator, or both.

Load a set of settings from the programming key previously saved via o65 function Replace the controllers factory settings with the present settings Service Status codes Temperature measured with S5 sensor Status on DI1 input. If an extra display type EKA A is connected, terminal 21 must be used for the display, and solely for the display.

  HOHNER B2A PDF

Electronic Controls: Evaporator Controls with Thermostatic Expansion Valves – Documents

The few selected settings will now be transferred 202s1 the menu. Push the upper or the lower button and find that parameter you want to change 3.

It depends on whether an application or a room is to be controlled and whether defrost is to be stopped based on time or based on temperature. If the time is passed, a defrost will be started.

Controller for temperature control – EKC 202D1 Manual

Here defrost can be started at fixed times of the day and night. S4 air temp Ther. Here are the messages that may appear: Here the signal may be used by the defrost function, so that the shortest and most 2021d defrost can take place.

This display will appear for up to 15 minutes after cooling resumes. Go wkc career section Working at Danfoss. Go to media section Danfoss Media Center. ON-time in minutes Min.

The time delay is set in minutes. There are several other functions for the alarm function as well as the light control, rail heat control and fans.