Site Loader

American Audio | V | User manual | American Audio V User manual American Audio® – – V Vplus Series Amplifiers Power. American audio V PLUS Pdf User Manuals. View online or download American audio V PLUS User Instructions. View and Download American Audio V/V user instructions online. PROFESSIONAL POWER AMPLIFIERS. V/V Amplifier pdf manual.

Author: Nebar Kagazshura
Country: Cape Verde
Language: English (Spanish)
Genre: Software
Published (Last): 14 May 2015
Pages: 138
PDF File Size: 5.32 Mb
ePub File Size: 13.73 Mb
ISBN: 202-7-30741-988-2
Downloads: 81061
Price: Free* [*Free Regsitration Required]
Uploader: Gardalkis

American Audio V3000/V2000 Stereo Amplifier User Manual

Thermal Protection – A single variable-speed fan on the V Vplus and dual variable speed fans on the V Vplus and V Vplus amplifiers provide adequate cooling. Typical speaker output using bare wire.

Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Insert bare wire into the binding post and tighten. To reduce the risk of electrical shock, do not remove cover.

Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. In the event of an electrical overload the breaker will pop-out.

Insert the banana jacks into the caps of the binding post, be sure that the banana jack is inserted securely to avoid the risk of it popping out.

Always use the 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc. Configuring the Low Cut Filter: This light may continue to glow briefly after main power has been turned off, this is normal. Bridged-Mono Mode Caution – The voltage across the output terminals of a bridged V Vplus series amplifier may equal or exceed volts RMS and may be as high as volts.


An ultrasonic network uncouples RF from the output and helps keep the amplifier stable with reactive loads. Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of overheating problems.

This booklet contains important information concerning the proper and safe operation of your new amplifier. Use channel two positive output terminal for the negative connection and the ameican one wudio output terminal for the positive connection. The diagram below detail the functions of each dip switch, the functions are also printed on the rear panel of the amplifier.

American Audio V3000 PLUS Manuals

Be sure your amplifier and all other audio equipment is powered down. Under heavy clipping activity lower the ameriican one gain control to reduce the risk of damage to your speakers and amplifier. For cable runs shorter than 20ft. Turn channel two gain up. Be sure that supplied voltage matches that of the required voltage of you amplifier. This fans are used to cool the internal parts of the amplifier when in use.

Connecting to the wrong voltage is dangerous and may damage the amplifier. The amplifier can operate at practically any power level without risk of overheating. These fans are used to cool the internal parts of the amplifier.

American Audio › V › Amplifier – Gearbase | DJResource

After inserting the wire into the binding post hole, screw akerican binding post cap down on the wire. Amplifiers arrive to you preset in the stereo operation mode. To reset the breaker, push it in.

To prevent electrical shock or fire hazard, do not expose this amplifier to rain or moisture. To print the manual completely, please, download it. Antes de usar este amplificador, lea mas advertencias en la guia de operacion. Channel 1 Frequency Adjustment. The front panel provides four holes used to screw the unit into a rack. Connect a XLR cable to the input of channel one.


Turning the knob in a clockwise direction will increase signal output. Cooling Fan – Dual speed cooling fans.

Channel 2 Frequency Akerican. Cooling Fan Dual speed cooling fans. Gain Controls A short circuit will usually be traced to a bad cable or a bad speaker and is rarely traced to the amplifier itself. Turn your amp on. The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground. Risiko – Elektrischer Schlag! These amplifiers are designed to provide a big impact in sound reproduction.

During low level output the fans run at normal speeds. Channel 1 subwoof frequency adj. The dip switches on the rear panel allows you to enable or disable the filter for each channel, as well as adjust either a 50Hz or 30 Hz cut-off. Power Switch – This switch controls the units main power. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping.

American Audio V User manual |

Inputs 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc. Use these connections to connect the output signal from a mixer, cross-over or EQ to your V Vplus series amplifier.

Use your front gain controls to regulate the output volume. The Output Short Circuit Protection protects the output devices of the amplifier from short circuits and stressful loads. Turn your equipment on your amplifier should always amwrican the last item you turn on.