Site Loader

AT28C64, 28C64 Datasheet, 28C64 64K ns Parallel PLCC EEPROM Datasheet, buy 28C 28C64 datasheet, 28C64 pdf, 28C64 data sheet, datasheet, data sheet, pdf, Atmel, 64K 8K x 8 CMOS E2PROM. 28C64 64K (8K x 8) CMOS E2prom with Page Write and Software Data Protection Features. Fast Read Access Time ns Automatic Page Write Operation.

Author: Gujinn Toll
Country: Ukraine
Language: English (Spanish)
Genre: Relationship
Published (Last): 14 August 2013
Pages: 383
PDF File Size: 5.68 Mb
ePub File Size: 12.71 Mb
ISBN: 236-8-62074-864-1
Downloads: 4563
Price: Free* [*Free Regsitration Required]
Uploader: Visar

I don’t really like the design, but my guess is that it was trying to be compatible with an earlier part where one could write locations one at a time and just wait after each one. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Here is the serial output. I have edited my question.

The same diagram shows CE being asserted followed by OE for a read cycle. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

28C64 Datasheet

Mar 27 ’13 at Sign up using Email and Password. I added ms delays between every control pin change and made sure the order was consistent with the datasheet, but still no luck. Thanks for the info.

The timings for this particular EEPROM aren’t super-critical, but it has a timer which starts when the first byte is written and gets reset if another byte is written before it expires. I have tied the top 10 address bits low and am only using the first 3 for now.

  CALORII TABEL PDF

28C64A-15 – 28C64A 64K 150ns Parallel EEPROM Technical Data

The chips are new, and I actually have two from 28c46 different manufacturers. That will make the remainder of your code much more readable. You have not indicated that you are doing anything with them?

Here is my code, sorry if it seems too cluttered: Post Your Answer Adtasheet By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Since I am only using the first three address pins, the rest are tied low. Sign up or log in Sign up using Google.

28C64 Datasheet(PDF) – ATMEL Corporation

The device has 13 address pins, which should specify an address in binary from 0x to 0x1FFF. I am using the Xicor 28C64AP chip datasheet. I have tested an earlier version of the above program with a static RAM chip and everything works great.

If it has, you’ll need to wire up all your address wires in order to disable it. Thanks for the response, supercat.

Any help would be much appreciated. Home Questions Tags Users Unanswered. That might help things. All behave the same. Sign up using Facebook. BTW, if the chips are equipment pulls as opposed to new parts, it’s possible that the “software protection” feature has previously been enabled.

  BEIJADA POR UM ANJO 2 PDF

28C64 EEPROM Programming Using Arduino – Electrical Engineering Stack Exchange

Looking at the datasheet on page 12 it shows a timing diagram and Chip Enable Access Time can be up to nS. Here is my code, sorry if it seems too cluttered:. PeterJ 16k 20 42 I wrote a program for the Arduino Uno datashret writes data to the first 4 addresses and then reads the data back.

Email Required, but never shown.

Initializing pins for write I’d recommend following that same sequence and also change your write sequence to follow the diagram on the following page. Also, I dayasheet suggest datassheet you should write a writebyte procedure which sets all address and data wires to output and puts proper values on them, ensures WE and OE are deasserted, asserts CE, asserts and release WE, and datxsheet CE, and a readbyte procedure which sets all address wires to output and puts proper values on them, sets all data wires to input, asserts CE and OE, samples all the data wires, and releases CE and OE.

One thing that is missing is on page 7 of the datasheet, it states that you need to write a sequence of codes to disable write-protection.